Parts & Accessories

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.

Who knew we could make a thru axle disappear? The Maxle Stealth offers a light, low profile alternative to Maxle Lite. Features - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench

Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This wheel kit is compatible with 1st generation non-disc Zipp NSW (before mid-2018). In The Box - 4 x 61803 bearings - 1 x 61903 bearing - 1 x 61804 bearing - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

Heavy duty and extra wide PVC rim strips for maximum tube protection.

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager 29"/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel - For specific compatibility, access 'WHEELS' tab on the Tech Site or contact Customer Service

When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.

Replacement Axle nuts for three speed Sturmey Archer hubs.

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

These rim valves are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager Tubeless Ready (TLR) wheels - Required for Bontrager's Tubeless Ready (TLR) system setup - Removable valve core for easy sealant fill - Silver MTB valve is compatible with all Bontrager Mountain wheels except: Line XXX, Kovee XXX, and Line Pro 40 - Alloy Road Tubeless Rim Valve is compatible with all Bontrager alloy TLR road wheels

The Drive Thru is a dummy hub or chain keeper that replaces your wheel while cleaning the chain. It is a fast and effective way to clean your chain between races or in your garage. It allows you to fully rotate your cranks and shift through your complete range of gears while protecting the frame. Installs simply with one hand, and is quick and easy to change between bikes. The Drive Thru is also great for packing the bike for transport. *This Drive Thru Value Meal includes three dummy axles with 1.0, 1.5 and 1.75 thread pitches and one pulley. - Value Meal includes 1.0, 1.5, and 1.75mm thread pitch dummy axles. - All Drive Thru dummy axles are 12mm in diameter. - Dummy axles are precision machined from 7075 aluminum and knurled for easy grip. - Pulleys are machined from durable Delrin. - Oil and solvent resistant O-rings - Lead-in threads designed for quick insertion into the frame - Simple, one-handed installation (no tools required)

Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed

- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces

- 11 Speed Freehub Body for Shimano and Sram Cassettes - XD Driver for SRAM Cassettes - 11 Speed Freehub has 28 points of engagement - XD Driver has 56 points of engagement - Fits Go-Devil Hubs

Parts for RaceFace hubs.

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs - Type: Solid Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 174mm - 1 axle per bag

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 16.9mm - Length: 15mm - 1 cone per bag Note: O-ring / seal not included. Check the seal groove closely. This cone has a narrower groove than cone CN-R002. COMPATIBLE HUBS: - 105 FH-5700, 9 speed (right side cone) - 105 SC 1051, 7 Speed Rear - RX100 A551, 8 Speed Rear - RSX 410, 7 Speed Rear - Deore LX M550, 7 Speed Rear - Deore Mtn LX M550, 7 Speed Rear

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

Convert your ISO, ISO B, or ISO Superboost DH rear hub to a Shimano Micro Spline compatible driveshell. The conversion kit is complete with an axle, adjustment clamp, driveshell and all driveshell internals for a plug-and-play swap. Micro Spline Driveshell Instructions - Compatible with Shimano Micro Spline cassettes; XTR, XT, and SLX - Compatible with ISO 142x12mm, ISO B 148x12mm, and ISO Superboost DH 157x12mm rear hubs.

- Extra security against theft - 5mm hex CrMo axle

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

- Colored rim decal kits to personalize your ride - Decals to fit 2 100w 26-inch rims

Origin-8's Track Cog Lock Ring with left-handed threading and 1.29 x 24tpi in a chrome finish completes your basic track cog locking needs.

Salsa springs for Flip-Off skewers

The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications

Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.